Simrad Suzuki Interface. All my fuel gauges and engine interface comes via the Lowra
All my fuel gauges and engine interface comes via the Lowrance engine interface module that plugs into Rigging Suzuki Mechanical Cable Engines with Gauge Interface Options PAGE 2 C10 Color Display with Engine Interface Cable 4 C10 Color Display with Simrad and Lowrance Multi All times are GMT -7. In this video it will show the complete process from beginning to end from finding the SDS main connector, making a wire extension, to connecting - - Suzuki Gateway 34923-96L13 and Simrad (https://www. This kit includes everything needed to connect your Suzuki outboard to This kit includes everything needed to connect your Suzuki Many Suzuki outboard engines have the ability to output engine data to a NMEA 2000® network. Engine Instances (port/center/starboard) can be set by Suzuki or by using Suzuki SMIS gauges. The time now is 10:03 PM. thehulltruth. Suzukis from 2016 onwards can use the special Engine Connect Gateway Interface cable that allows any compatible Lowrance or Simrad display to activate the Suzuki - Marine Electronics Forum (https://www. 3K views 3 replies 4 participants last post by TeamJib Feb 1, 2023 Apoland Discussion starter A few years ago Suzuki released 2 x new interface cables with a different software design to the earlier models. 10ft cable Suits DF 40 to SUZUKI GENUINE ENGINE CONNECT CABLE THIS CABLE IS FOR CONNECTING SUZUKI ENGINE SDS DATA TO SIMRAD/LOWRANCE Hello all! about 1. (Figure 3. 9HP–30HP engines. DF9. 5 interface and sds adapter cable. I have all the correct hardware and I hooked everything together What do I need to connect up my 2008 Suzuki 150 DF outboard to my SIMRAD NSS9 Evo2 so I can use the screen for engine gauges and start watching and logging fuel use With the engine key turned on, in either of the Simrad menus you can open the netwoek menu/device list and select the Suzuki device, it will show you the software version This kit includes everything needed to connect your Suzuki outboard to your Simrad/Lowrance MFD GPS Display, to utilize Suzuki data integration. I had analogue gauges instead of digital from The C10 is a Simrad IS35 square 4” display that has been customised for Suzuki. It can show Suzuki OEM Engine Interface Cable 990C0-88149-357 The most important part of the SMIS data system is the engine interface. The new cables run software with the file extension “. B) If the engine instances are not set by Suzuki then you may need to manually Installed v3. The data gets sent from the interface cable to the network, and then any compatible display on the I went NMEA 2000 with Suzuki and Lowrance gauges and chartplotter. It includes information on compatible devices, data output, and network setup. Includes interface cable, gateway connect, and NMEA 2000 backbone. However, for SPC 2. 5 years ago I setup a nmea 2000 network for my twin 2020 df150 application, a simrad go9, and a simrad go12. 3. its easiest to do this on the Lowrance display, just make sure engine key is turned on where it beeps but dont start the . All of the engine information comes from the engine interface cable. com/marine-electronics-forum-19/) - - Suzuki Fuel Data Manager or Engine Interface Cable (https://www Suzuki ® Engine Connection for NMEA 2000® Messages Many Suzuki outboard engines have the ability to output engine data to a NMEA 2000® network. Simple and easy to install “plug and play” This user guide provides instructions on connecting a Suzuki Outboard engine to a NMEA 2000® network. Gauge not included. Compatible with Lowrance/Simrad MFDs. It ONLY works with Suzuki engine interface cables via the NMEA2000 network. I've done the auto select on the simrad If you want fuel consumption data you may want to add the Fuel Data Manager, you can order it direct from Simrad, and it should If you have a multi-engine boat (serial numbers 310001 or higher) AND a digital C10 Suzuki gauge AND K-Line boat-side wiring harness (not CAN) AND are trying to connect a Simrad Mult In this bulletin, your suggested route is specified for Suzuki motors using SPC 1. 0 controls. 9B thru Suzuki Outboard Engine Interface Cable is an integral part of the SMIS data system, allowing DF40 thru DF300 Suzuki Outboards to be connected to I recently purchased a 2020 Crest Caribbean pontoon and I'm adding the Suzuki engine data to the Simrad. Page 1 of 2 1 2 > Show 40 post (s) from this thread on one page Powered by vBulletin® Our Lead Engineer, Brian Rupp, walks you through the steps on how to sync your engine up to your Simrad on Diamantes, Lago Z's, and any Lago X's that upgrade Essential Guide for NMEA 2000 Engine Interface, detailing compatibility, installation, features, and data capabilities for various outboard engine brands. swup” Suzuki Outboard Engine Interface Cable is an integral part of the SMIS data system, allowing DF40 thru DF300 Suzuki outboards to be connected to the system. This user guide provides instructions on connecting a Suzuki Outboard engine to a NMEA 2000® network. com/marine-electronics-forum/1276417-suzuki-gateway-34923-96l13-simrad. html) If you do stay with the interface cable, Id suggest getting the Suzuki Connect Gateway version of the interface because as well as the normal engine data, it sends fault When you install it you need to configure the interface. NMEA network is properly working as I can see all devices EXCEPT the suzuki on the list. 0, the gateway I have Suzuki/Simrad connection Jump to Latest 5. Ok. This output from the engine can be displayed on Navico Multi‐Function Displays such as the OEM Suzuki kit for 9.
